NEW!

IMS's MDrive34Plus Motion Control offers system designers a low cost, intelligent motion controller integrated with a NEMA 34 high torque brushless motor and a +12 to +75 volt microstepping driver.

The unsurpassed smoothness and performance delivered by the MDrive34Plus Motion Control are achieved through IMS's advanced 2nd generation current control. By applying innovative techniques to control current flow through the motor, resonance is significantly dampened over the entire speed range and audible noise is reduced.

The MDrive34Plus accepts a broad input voltage range from +12 to +75 VDC, delivering enhanced performance and speed. Oversized input capacitors are used to minimize power line surges, reducing problems that can occur with long runs and multiple drive systems. An extended operating range of -40° to +85° C provides long life, trouble free service in demanding environments.

Standard features available in the MDrive34Plus Motion Control include four +5 to +24 volt general purpose I/O lines, one 10 bit analog input, 0 to 5 MHz step clock rate, 20 microstep resolutions up to 51,200 steps per revolution, and full featured easy-to-program instruction set.

Expanded features in the MDrive34Plus² version include eight +5 to +24 volt general purpose I/O lines and the capability of electronic gearing by following a rotary or linear axis at an electronically controlled ratio, or an output clock can be generated fixed to the internal step clock.

All MDrive34Plus Motion Control are available with optional closed loop control. This increases functionality by adding stall detection, position maintenance and find index mark.

The closed loop configuration is added via a 512 line (2048 edge) optical encoder with index mark, internal to the unit so there is no increase in length. Or, for an expanded choice of line counts and resolutions with MDrive34Plus² versions only, closed loop control is available with an interface to a remotely mounted user-supplied external encoder.

The MDrive communicates over RS-422/485 which allows for point-to-point or multiple unit configurations utilizing one communication port. Addressing and hardware support up to 62 uniquely addressed units communicating over a single line. Baud rate is selectable from 4.8 to 115.2kbps.

Optional communication protocols include CANopen. The CAN bus is 2.0B active (11 and/or 29 bit) and is capable of all standard frequencies from 10 kHz to 1 MHz. CANopen features include node guarding, heartbeat, SDOs and PDOs. Highlights include variable PDO mapping and extended node indentifier.*

Available motor configurations include a single shaft rotary motor and a linear actuator with long life Acme screw*. Rotary versions are available in three motor lengths. Interface connections are accomplished using 12.0" (30.5 cm) flying leads and for expanded MDrivePlus² versions using pluggable locking wire crimp connectors.

The MDrive34Plus is a compact, powerful and inexpensive solution that will reduce system cost, design and assembly time for a large range of brushless motor applications.

FEATURES:

	Highly integrated microstepping driver,
	motion controller and NEMA 34 high torque
	brushless motor
	Advanced 2nd generation current control for
	exceptional performance and smoothness
	Singe supply +12 to +75 VDC
	Low cost
	Extremely compact
	Available options: long life linear actuator*;
	internal magnetic encoder for closed loop
	control; integrated planetary gearbox;
	control knob for manual positioning; linear
	slide
	3 rotary motor lengths available
	Auxiliary logic power supply input
	20 microstep resolutions up to 51,200 steps
	per rev including: degrees, metric, arc
	minutes
	Open or optional closed loop control
	Programmable motor run and hold currents
	Optically isolated logic inputs will accept +5
	to +24 VDC signals, sourcing or sinking
	One 10 bit analog input selectable: 0 to +10
	VDC, 0 to +5 VDC, 0-20 mA, 4-20 mA
	0 to 5 MHz step clock rate selectable in
	0.59 Hz increments
	RS-422/485 or optional CANopen*
	communications
	62 software addresses for multi-drop
	communications
	Simple 1 to 2 character instructions
	Interface options: 12.0" (30.5 cm) flying
	leads

FEATURES FOR EXPANDED PLUS²:

	8 I/O lines, +24 VDC tolerant sourcing or
	sinking, inputs and outputs
	Electronic gearing
	Optional external / remote encoder for
	closed loop control
	High speed position capture input or trip
	output
	Pluggable locking wire crimp interface

*Consult Servo Systems Co. for availability.

Please contact our Sales Staff for pricing information.